How to Install a Bath Tub in Your Bathroom
How to Install a Bath Tub in Your Bathroom
Blog Article
Have you been hunting for content about How to Install a Bathtub?
Setting up a bath tub isn't specifically brain surgery, yet it does call for strong plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately difficult project. If the old tub is readily available, the project can move rapidly; if you have to open a wall to remove the old tub and position the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need a helper to move out the old tub and set in the brand-new one. See to it you have actually qualified yourself for the job and are comfortable trying it. As opposed to working with a service provider to take control of a halfway-completed job, it is better to consider employing one prior to you start. Chances are you might require a specialist plumber to make tube links.
This write-up will certainly assist you set up a new tub in your restroom if you have already bought a brand-new bathtub and also do not need to alter the arrangement of your previous water supply pipes.
Your tools and also product list ought to make up the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is detach the supply of water. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic due to the limited accessibility that is commonly the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipes. Once the supply pipes have actually been eliminated, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, then you will require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making sure that the washers remain in area between the faucet and also the sink. Protect the faucet in place with the maker provided backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Bath tub
Making use of the two wood boards under its feet, put the bath tub in the called for position. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following goal is to guarantee that the tub is leveled all round. This can be attained by examining the spirit level and changing the feet on the tub till the level reads level.
To set up taps, fit all-time low of the outermost adaptable faucet connector to the appropriate supply pipe by making a compression join; after that do the exact same for the various other faucet.
Activate the water supply and check all joints as well as new pipework for leaks as well as tighten them if needed. Fill up the tub and also check the overflow outlet and the regular electrical outlet for leakages.
Lastly, take care of the bath paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bathtub should wait until the bath tub has actually been made use of a minimum of once as this will settle it right into its last setting.
Getting ready for the Setup
First of all, the supporting frame provided with the bathroom must be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the tap features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final placement.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break a stiff seal, creating the water to penetrate the wall surface between the bath and also the tiling, resulting in issues with wetness and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealant can split rather early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly readily available on the market. It is suggested to fit the tiles using waterproof or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that blog posting about A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the internet. Sharing is nice. Helping people is fun. Thank you for your time. Visit again soon.
Click Here To Find Out More Report this page